 |
| Quantity: | |
|---|---|
PUL1235A/3
1. Machine Purpose:
a) This machine can be used for 3-sides CNC punching of the U beam with equal cross section of the truck/lorry.
b) The machine has the characteristics of high processing precision, fast punching speed and high production efficiency.
c) The whole process is fully automatic and flexible, which can adapt to the mass production of longitudinal beam, and can be used to develop new products with small batch and many kinds of production.
The production preparation time is short, which can greatly improve the product quality and production efficiency of the automobile frame.
2. MainTechnical specification
Data of U beam before punching | Data of U beam before punching | σb=510-890 MPa |
Length of U beam | 4000～ (+) | |
Inside width of U beam web | 150-340 mm (+) | |
U beam flange height | 60 (±) | |
U beam thickness | 4-10 mm | |
Fillet radius | R (+) | |
Longitudinal straightness deviation of Web surface | 0.1%, ≤/ overall length | |
Longitudinal flatness deviation of flange surface | /m, ≤/ overall length | |
Maximum twist | / overall length | |
Angle between flange and web | 90o±1 | |
Data of U beam after punching | Punching diameter of Web | Maximum Φ 65mm. Minimum equals plate thickness |
Punching diameter of flange | Maximum Φ 21. Minimum equals plate thickness | |
The minimum distance between the centerline of the hole on the web closest to the inner surface of the flange | 20mm when Hole diameter ≤ Φ 13mm 25mm when Hole diameter ≤ Φ 23 50mm when Hole diameter＞Φ 23mm | |
The minimum distance between the U beam inner side web surface and the centerline of flange hole | 25 mm | |
The punching accuracy shall be controlled within the following range (except for the range of 200 mm at both ends) and the centerline distance accuracy between holes | Tolerance value of hole spacing in X direction: ± 0.3mm/2000mm； ±0.5mm/12000mm Tolerance value of group hole distance in Y direction：±0.3mm | |
Accuracy of the Distance from hole centerline to the flange inner edge | ± | |
Module position and punching travel of punching press | Numerical control punching machine for movable web plate | 18 modules, straight line. |
CNC punching press for small web plate | 18 modules, straight line, 5 modules of Φ25. | |
Fixed wing plate CNC punch | 6 modules, straight line. | |
Movable flange CNC punching machine | 6 modules, straight line. | |
Punching travel of main machine | ||
Production Efficiency | When the length of the U beam is 12 meters and there are about 300 holes, the punching time is about 5.5 minutes | |
Machine Overall Size | Length x Width x Height | about 37000mm x 8500mmx 4000mm. |
Loading and unloading trolley | Move travel | about 2000mm |
Move speed | about 4m/min | |
Stacking height | about 500mm | |
Magnetic In-feeding device / Magentic downloading device | Horizontal travel | about 2000mm |
Horizontal motor power | 0.75kW | |
Vertical travel | about 600mm | |
Vertical motor power | 2.2kW | |
Number of electromagnets | 10 | |
Electromagnet suction force | 2kN/each piece | |
Infeeding Manipulator | Maximum speed | /min |
X-axis travel | about 3500mm | |
Movable CNC Punching Press for web | Nominal force | 800kN |
Punch hole diameter types | 9 | |
Module number | 18 | |
X-axis travel | about 400mm | |
X-axis maximum speed | 30m/min | |
Y- axis travel | about 250 mm | |
Y-axis maximum speed | 30m/min | |
Maximum punch diameter | Φ23mm | |
CNC Punching Press for small web plate | Nominal force | 800kn |
Punch type | 9 | |
Module number | 18 | |
Y-axis stroke | About 250mm | |
Maximum speed of y-axis | 30 m/min | |
Maximum punch diameter | Φ23 mm | |
Main CNC Punching Press for web | Nominal force | 20000kN |
Punch hole diameter types | 10 | |
Module number | 10 | |
Y- axis travel | about 250mm | |
Y-axis maximum speed | 30m/min | |
Maximum punch diameter | Φ65mm | |
Middle manipulator | Maximum speed | 40m/min |
X-axis travel | about 2000 mm | |
Fixed Flange CNC Punching Press | Nominal force | 650kN |
Punch hole diameter types | 6 | |
Module number | 6 | |
Z-axis travel | about 100mm | |
Z-axis maximum speed | 10 m/min | |
Maximum punch diameter | Φ23mm | |
Movable Flange CNC Punching Press | Nominal punching force | 650kN |
Punching hole diameter types | 6 | |
Module number | 6 | |
Y-axis travel | 160mm | |
Y-axis maximum speed | 10 m/min | |
Z-axis travel | about 100mm | |
Z-axis maximum speed | 10 m/min | |
Maximum punching diameter | Φ23mm | |
Output material manipulator | Maximum speed | /min |
X axis travel | About 3500mm | |
Magnetic downloading device | Horizontal movement travel | About 2000mm |
Horizontal movement motor power | 0.75kw | |
Vertical movement travel | About 600mm | |
Vertical movement motor power | 2.2kw | |
Electromagnetic Numbers | 10 | |
Electromagnetic Sucking Force | 2kN/ each | |
Hydraulic system | system pressure | 24MPa |
Cooling mode | Oil cooler | |
Pneumatic system | working pressure | 0.6 MPa |
Electrical system | Siemens 840D SL |
No. | Name | Brand | Country | Remark |
1 | CNC | Siemens 840D SL | Germany | |
2 | Servo motor | Siemens | Germany | |
3 | Precision linear sensor | Balluff | Germany | |
4 | Hydraulic system | H+L | Germany | |
5 | Other main hydraulic components | ATOS | Italy | |
6 | linear guide rail | HIWIN | Taiwan, China | |
7 | Wide guide rail | HPTM | China | |
8 | Precision ball screw | I+F | Germany | |
9 | Screw support bearing | NSK | Japan | |
10 | Pneumatic components | SMC/FESTO | Japan / Germany | |
11 | Single air bag cylinder | FESTO | Germany | |
12 | Elastic coupling without backlash | KTR | Germany | |
13 | Frequency converter | Siemens | Germany | |
14 | computer | LENOVO | China | |
15 | Drag chain | IGUS | Germany | |
16 | Automatic lubrication device | HERG | Japan | Thin oil |
4. Work Environment:
1).Power supply： 3 phase 5 lines 380±10%V 50±1Hz
(as per Brazil local voltage)
2).Compressed air pressure： ≥0.5MPa
3).Temperature： 0
4).Humidity： ≤75%
1. Machine Purpose:
a) This machine can be used for 3-sides CNC punching of the U beam with equal cross section of the truck/lorry.
b) The machine has the characteristics of high processing precision, fast punching speed and high production efficiency.
c) The whole process is fully automatic and flexible, which can adapt to the mass production of longitudinal beam, and can be used to develop new products with small batch and many kinds of production.
The production preparation time is short, which can greatly improve the product quality and production efficiency of the automobile frame.
2. MainTechnical specification
Data of U beam before punching | Data of U beam before punching | σb=510-890 MPa |
Length of U beam | 4000～ (+) | |
Inside width of U beam web | 150-340 mm (+) | |
U beam flange height | 60 (±) | |
U beam thickness | 4-10 mm | |
Fillet radius | R (+) | |
Longitudinal straightness deviation of Web surface | 0.1%, ≤/ overall length | |
Longitudinal flatness deviation of flange surface | /m, ≤/ overall length | |
Maximum twist | / overall length | |
Angle between flange and web | 90o±1 | |
Data of U beam after punching | Punching diameter of Web | Maximum Φ 65mm. Minimum equals plate thickness |
Punching diameter of flange | Maximum Φ 21. Minimum equals plate thickness | |
The minimum distance between the centerline of the hole on the web closest to the inner surface of the flange | 20mm when Hole diameter ≤ Φ 13mm 25mm when Hole diameter ≤ Φ 23 50mm when Hole diameter＞Φ 23mm | |
The minimum distance between the U beam inner side web surface and the centerline of flange hole | 25 mm | |
The punching accuracy shall be controlled within the following range (except for the range of 200 mm at both ends) and the centerline distance accuracy between holes | Tolerance value of hole spacing in X direction: ± 0.3mm/2000mm； ±0.5mm/12000mm Tolerance value of group hole distance in Y direction：±0.3mm | |
Accuracy of the Distance from hole centerline to the flange inner edge | ± | |
Module position and punching travel of punching press | Numerical control punching machine for movable web plate | 18 modules, straight line. |
CNC punching press for small web plate | 18 modules, straight line, 5 modules of Φ25. | |
Fixed wing plate CNC punch | 6 modules, straight line. | |
Movable flange CNC punching machine | 6 modules, straight line. | |
Punching travel of main machine | ||
Production Efficiency | When the length of the U beam is 12 meters and there are about 300 holes, the punching time is about 5.5 minutes | |
Machine Overall Size | Length x Width x Height | about 37000mm x 8500mmx 4000mm. |
Loading and unloading trolley | Move travel | about 2000mm |
Move speed | about 4m/min | |
Stacking height | about 500mm | |
Magnetic In-feeding device / Magentic downloading device | Horizontal travel | about 2000mm |
Horizontal motor power | 0.75kW | |
Vertical travel | about 600mm | |
Vertical motor power | 2.2kW | |
Number of electromagnets | 10 | |
Electromagnet suction force | 2kN/each piece | |
Infeeding Manipulator | Maximum speed | /min |
X-axis travel | about 3500mm | |
Movable CNC Punching Press for web | Nominal force | 800kN |
Punch hole diameter types | 9 | |
Module number | 18 | |
X-axis travel | about 400mm | |
X-axis maximum speed | 30m/min | |
Y- axis travel | about 250 mm | |
Y-axis maximum speed | 30m/min | |
Maximum punch diameter | Φ23mm | |
CNC Punching Press for small web plate | Nominal force | 800kn |
Punch type | 9 | |
Module number | 18 | |
Y-axis stroke | About 250mm | |
Maximum speed of y-axis | 30 m/min | |
Maximum punch diameter | Φ23 mm | |
Main CNC Punching Press for web | Nominal force | 20000kN |
Punch hole diameter types | 10 | |
Module number | 10 | |
Y- axis travel | about 250mm | |
Y-axis maximum speed | 30m/min | |
Maximum punch diameter | Φ65mm | |
Middle manipulator | Maximum speed | 40m/min |
X-axis travel | about 2000 mm | |
Fixed Flange CNC Punching Press | Nominal force | 650kN |
Punch hole diameter types | 6 | |
Module number | 6 | |
Z-axis travel | about 100mm | |
Z-axis maximum speed | 10 m/min | |
Maximum punch diameter | Φ23mm | |
Movable Flange CNC Punching Press | Nominal punching force | 650kN |
Punching hole diameter types | 6 | |
Module number | 6 | |
Y-axis travel | 160mm | |
Y-axis maximum speed | 10 m/min | |
Z-axis travel | about 100mm | |
Z-axis maximum speed | 10 m/min | |
Maximum punching diameter | Φ23mm | |
Output material manipulator | Maximum speed | /min |
X axis travel | About 3500mm | |
Magnetic downloading device | Horizontal movement travel | About 2000mm |
Horizontal movement motor power | 0.75kw | |
Vertical movement travel | About 600mm | |
Vertical movement motor power | 2.2kw | |
Electromagnetic Numbers | 10 | |
Electromagnetic Sucking Force | 2kN/ each | |
Hydraulic system | system pressure | 24MPa |
Cooling mode | Oil cooler | |
Pneumatic system | working pressure | 0.6 MPa |
Electrical system | Siemens 840D SL |
No. | Name | Brand | Country | Remark |
1 | CNC | Siemens 840D SL | Germany | |
2 | Servo motor | Siemens | Germany | |
3 | Precision linear sensor | Balluff | Germany | |
4 | Hydraulic system | H+L | Germany | |
5 | Other main hydraulic components | ATOS | Italy | |
6 | linear guide rail | HIWIN | Taiwan, China | |
7 | Wide guide rail | HPTM | China | |
8 | Precision ball screw | I+F | Germany | |
9 | Screw support bearing | NSK | Japan | |
10 | Pneumatic components | SMC/FESTO | Japan / Germany | |
11 | Single air bag cylinder | FESTO | Germany | |
12 | Elastic coupling without backlash | KTR | Germany | |
13 | Frequency converter | Siemens | Germany | |
14 | computer | LENOVO | China | |
15 | Drag chain | IGUS | Germany | |
16 | Automatic lubrication device | HERG | Japan | Thin oil |
4. Work Environment:
1).Power supply： 3 phase 5 lines 380±10%V 50±1Hz
(as per Brazil local voltage)
2).Compressed air pressure： ≥0.5MPa
3).Temperature： 0
4).Humidity： ≤75%
